YONGNUO YN560-TX PRO Transmitter & Radio System – Announced



YongNuo have announced the YN560-TX PRO, TTL and HSS enabled Radio Transmitter, and next generation 560 PRO Radio System, which will finally integrate the YN560 and YN-622 Radio Systems into one compatible system.

The new 560 PRO Radio System also now features auto sensing radio Receiver modes for Canon, Nikon, and Sony camera systems

NOTE – It appears YN622 enabled flashes and triggers will only be functional as receiver/slave units in the YN560 PRO system. While previous YN560 and RF602 / 603 enabled gear are compatible as transmitter or receiver where applicable.


The YN560-TX PRO transmitter for Canon will be available first, with Nikon and Sony versions to follow.

The new transmitter features control for 5 Groups, in TTL, Manual, and GR Group Modes (Mixed TTL & M). With remote Zoom control available where applicable.

NOTE – TTL and HSS will only be possible with the products originally supporting these functions.






  • Provides Auto Sensing Radio Receiver Modes for Canon, Nikon, and Sony camera systems.
  • Where applicable supports full TTL, HSS, Remote Manual, Multi, and Remote Zoom.




  • YN-622 / II, and YN968, YN685, etc flashes will require a firmware update to receive YN560 PRO signal.
  • RF603, YN560 III/IV, YN660, series can directly receive the YN560 PRO radio signal already.
  • New Flash models like the YN200 and YN862 also directly receive the YN560 PRO radio signal.


The chart below from YongNuo shows compatibility through the system, with the red square indicating where TTL and HSS is supported.






  • Range – To 100m
  • 2.4GHz Frequency
  • Flash Modes – TTL / M / Multi / GR
  • HSS to 1/8000th
  • Second Curtain Sync
  • FEC / FEB – 1/3rd Increments (±3 Stops)
  • FEL (Flash Exposure Lock)
  • Manual Power – 1/128 – 1/1 Output (1/3 Stop Increments)
  • Flash Ratio Control – 1:8 – 1:1 – 8:1 (1/2 Stop Increments)
  • Remote Flash Zoom By Group
  • Group Style Mode – A / B / C / D / E  (5 Groups)
  • 16 Channels
  • Wireless ID 0000-9999
  • Compatible with 560 PRO Radio Enabled Flashes and Receivers
  • Large Dot Matrix LCD Display with Adjustable Back Light
  • Backlit Buttons
  • Modeling flash
  • Auto Memory Function
  • AF Assist Light
  • Micro USB Port for Firmware Upgrades
  • Lever Lock Foot
  • Powered by 2 AA Batteries
  • Size – Approx. 67.7 x 66.7 x 81.3mm
  • Weight – Approx. 110 g (Excluding Batteries)



Based on the same body as the current YN-E3-RT Transmitter, the YN-560TX PRO are powered by 2 AA batteries and provide a Micro USB port for firmware updates.

An AF Assist Light, and quick lever lock foot are provided. There is no sync port, or shutter release port included though.






Type:  2.4G On-camera Speedlite transmitter

Modes: E-TTL II/E-TTL Autoflash, Manual flash, Multi flash, Gr flash

Channel: Ch1 – 16

ID: 0000-9999

Slave unit control: Up to 5 groups (A/B/C/D/E)

Transmission distance: Approx. 100 m

Flash ratio control: 1:8 – 1:1 – 8:1, 1/2-stop increments

FEC: ±3 stops in 1/3-increments

High-speed sync: Provided

Manual flash: 1/1 – 1/128 power (1/3-stop increments)

Stroboscopic flash: Provided (1 – 500 Hz)

AF Assist Beam Emitter: Provided

Firmware update: Provided

Power source: 2 AA / LR6 alkaline batteries, Ni-MH  batteries

Dimensions: Approx. 67.7x 66.7x 81.3mm

Weight: Approx. 110g (excluding batteries)





The YN560-TX PRO for Canon are available now from $59 –

Amazon, UKEbay

With Nikon and Sony version to follow.


YongNuo – Website

  1. Paul 10 months ago

    Would you possibly have an email contact at yongnuo as I would like to review their new 560 TX-Pro as well as the yn-200 flash on my youtube channel.

    I’ve covered their products in the past with massive response. eg., 1. https://www.youtube.com/watch?v=ImBL6xtGjSo&t=8s 2. https://www.youtube.com/watch?v=ETzG0W3tjew&t=4s

    I will appreciate your kind support if possible.

    Best regards,

    Paul Phillips

    • Author
      FLASH HAVOC 10 months ago

      Hi Paul,

      Its hard to get a response from YongNuo directly, you’re likely best to contact them via their Ebay store as they usually reply there.

  2. Paul 9 months ago

    Hi! I bought the 560 TX-Pro. But how to start working with a YN560 III?

    • Nor Izwan 5 months ago

      I’m having the same problem.The TX Pro can only fire the flash, but can’t adjust the power and the zoom.. Im getting frustrated. Had to switch back to my old yn560tx for shoots.

  3. domino 8 months ago

    Hi all

    I wan to ask, can you control both flashes in same time on different radio frequencies?

    I mean if it is possible together shoot with yn560iii and yn968 ?

    And also be able to use ttl on yn968

  4. mike 8 months ago

    I have the Nikon version of the YN560 TX pro as an upgrade from the 622 system using YN968N flashes. However the Pro transmitter won’t work as TTL does on the 622 system. I replaced the 622 so i can use the YN200 which has yet to turn up This wasn’t really what I was after.

    • Artyom 8 months ago

      I could be wrong, but I have the same setup, I think for now TTL doesn’t work with YN968N because Yongnuo hasn’t released the firware yet.. they say in the YN560 TX pro that you need latest firmware, but the 1.09 for 968N is from 2017. So in 560 mode it works in manual mode, but for now not in TTL. And in the YN560 TX pro manual-book I discovered that they released the YN968N II, never heard about it before (-I have 5 YN560 III and 4 YN968N) ; the fun never ends with this brand 🙂

  5. Jay Chan 7 months ago

    I have a YN200 and a YN560 TX Pro Nikon version. Please teach me how to switch on the high speed sync for both devices. The user manual does not show me how to do it but only stated that it allows HSS. Thank you

  6. Jim Leonardo 7 months ago

    I have the same issue as Jay Chan but with Canon. I’m using the YN 685 and 560TX Pro. How do we make this work? Help please 🙂

  7. Jim Leonardo 7 months ago

    Ok, so now I got the two to at least talk to each other. Flash in RF603 slave mode and TX Pro in Master mode. But, I cant get HSS to show up on both the flash and transmitter at the same time. If the transmitter has it, the flash will not receive the signal while in ETTL mode. And if I change flash to Manual with HSS (rf603slave) I get banding after 1/200th. This is frustrating…

    • Ren Faustino 7 months ago

      I’m having the same problems. I can’t figure out how to enable HSS while the YN685 is in the rf603. Already updated the firmware to the latest version

  8. Jerry 5 months ago

    Can the yn560tx pro trigger all protocols simultaneously? like i have the 622, 603 and 560 versions of the flash slaves and i want all to trigger at once.

  9. Nor Izwan 5 months ago

    Just Got My Yn560TX Pro, works flawlessly on my yn660 and yn685. Unfortunately, on my older yn560iii, it can only fire but not adjust the power and the zoom. I read the manual three times but cannot find a way. Need Help.!!

  10. Uncool 1 month ago

    I’ll add my name to the list of people who can’t figure out how change power on a YN560 III with the YN560TX-Pro.
    Has anyone been able to do this and if so, how?

  11. Vmp 2 weeks ago

    Does anyone know how to switch yn560tx Pro to multi flash mode?

Leave a reply

Your email address will not be published. Required fields are marked *


Anti-Spam Quiz:


Log in with your credentials

Forgot your details?